 |
|
 |
6504 NW. 77th Court. Miami,
Florida 33166
USA • Phone: 305-556-6251
Fax: 305-556-6256
sales@ac1supply.com |
|
|
| |
|
 |
| Curtain Wall / Bypass Connections |
FastClip™ Slide Clips (FCSC)
Provide for vertical building movement up to 3"
ClarkDietrich FastClip™ Slide Clip deflection clips are used to attach exterior curtain-wall
studs to the building structure and provide for vertical building movement independent of
the cold-formed steel framing. A FastClip deflection clip installs quickly with screws or
powder-actuated fasteners, and provides adjustable standoff to ensure a plumb wall
plane. FastClip Deflection Screws are provided with each clip to ensure friction-free
sliding. Each clip is also embossed with fastening patterns to ensure accurate placement
of fasteners.
Meets ICC ESR-2570 in compliance with the 2012 International Building Code® (IBC)
and International Residential Code® (IRC), as well as the 2010 California and Florida
Building Code.
• Vertical movement up to 3" (1-1/2" up and 1-1/2" down).
• 3-1/2" FastClip™ permits up to 1" of standoff from the primary frame.
• FastClip™ Deflection Screws (included) provide frictionless slip connection.
• U.S. Patent No. 6,688,069
|
 |
Fast Strut™ (FS12, FS15)
Used for large standoff conditions
ClarkDietrich Fast Strut™ curtain-wall connector employs the Fast Clip™ technology for
curtain-wall stud attachment and is commonly used when large stand-off conditions exist.
Fast Strut™ products are available in standard lengths of 12-1/4" and 15-1/4" and custom
lengths of up to 24" long to allow framing attachment well beyond the perimeter of the
structural steel or when the spandrel beams are set back from the edge of the structure.
Struts are attached to the underside of structural members with screws, welds, or
powder-actuated fasteners. FastClip Deflection Screws are provided with each strut to
ensure friction-free sliding. Each strut is also embossed with fastening patterns to ensure
accurate placement of fasteners.
• Vertical movement up to 2-1/2" (1-1/4" up and 1-1/4" down).
• Allows for standoff from the primary frame.
• FastClip™ Deflection Screws (included) provide frictionless slip connection.
• U.S. Patent No. 6,688,069
|
 |
FastHook FastClip™ (FHCL, FHCR)
Enables faster installation by eliminating the need for temporary clamps
ClarkDietrich FastHook FastClip™ is a revolutionary new technology that allows the
installer to temporarily hang the clip in place on pour stop or perimeter angle, freeing
both hands for the installation of permanent fasteners. ClarkDietrich FastHook deflection
clips are used to attach exterior curtain-wall studs to the building structure and provide
for vertical building movement independent of the cold-formed steel framing.
Available in Right-hand and Left-hand versions. FastClip Deflection Screws are provided
with each clip to ensure friction free sliding. Each clip is also embossed with fastening
patterns to ensure accurate placement of fasteners.
• Vertical movement up to 3"(1-1/2" up and 1-1/2" down).
• Positively attached. Eliminates friction-held and temporary fastening.
• FastClip™ Deflection Screws (included) provide frictionless slip connection.
• U.S. Patent Pending.
 |
 |
Flat Tail™ Slide Clip (FTSC)
Allows for vertical building movement and provides up to 3" of horizontal standoff
ClarkDietrich Flat Tail™ Slide Clip is used to attach exterior curtain-wall studs
(3-5/8” - 8” widths) to the building structure and provides for vertical building movement
independent of the cold-formed steel framing. A Flat Tail Slide Clip provides variable
standoff and eliminates the need for shims or additional framing components.
The Flat Tail Slide Clip fastens to the floor/ceiling beam and is secured to the stud with
FastClip Deflection Screws. The clip restricts lateral movement, but enables the building
structure to move vertically.
• Quick installation.
• Provides up to 3” of horizontal standoff.
• Vertical movement up to 2-1/4” (1-1/8” up and 1-1/8” down).
• FastClip™ Deflection Screws (included) provide frictionless slip connection.
• One clip accommodates all stud flanges.
 |
 |
QuickClip™ (QC3, QC4, QC6, QC8)
Allows for vertical building movement and provides up to 3" of horizontal standoff
ClarkDietrich QuickClip™ vertical slide clips are used to attach exterior curtain-wall studs
to the building structure and provide for vertical building movement independent of the
cold-formed steel framing. A QuickClip™ slide clip provides variable standoff and
eliminates the need for shims or additional framing components. The QuickClip™
slide clip simply twists into place and fastens to the floor/ceiling beam. The clip restricts
lateral movement, but enables the building structure to move vertically.
• Quick installation—twist and fasten.
• Horizontal stand-off up to 3”.
• One-piece for right- or left-handed attachment.
• Accommodates 1-5/8" and 2" flanges.
• Custom sizes available.
• U.S. Patent No. 5,836,133 of B&D Industries.
|
 |
Slide Clip™ (SD)
An edge-of-slab deflection clip for curtain-wall framing
ClarkDietrich SD slide clips are used to attach exterior curtain-wall studs to the building
structure and provide for vertical building movement independent of the cold-formed
steel framing. SD slide clips are used in by-pass framing situations and are normally
welded or otherwise fastened to the vertical leg of a structural angle at the floor or roof
edge. Normally a stand-off exists between the structural angle and the inside flange of
the curtain-wall stud. This will require the installation of an extra stud piece to bridge the
stand-off. In order to avoid the extra installation costs, the ClarkDietrich FastClip™
products are recommended in place of the SD clip.
• First-generation low-cost deflection clip.
• Offset for easier welding.
• Requires additional framing components for horizontal stud adjustment.
|
 |
TWIN TRAC (Superior Stucco Reinforcing)
No. 17 1- 1/2" x 1-1/2" - Alternative to 2.5 diamond metal lath
Structalath Twin Trac is an innovative self furring reinforcing lath that simplifies the
attachment of lath to wood and steel studs. It is excellent for commercial construction;
Twin Trac has all the great features of regular Structalath with the addition of eight
secondary cold-rolled longitudinal wires that add strength to form a 'track' for convenient
attachment. Twin Trac can be substituted wherever 2.5 metal lath has been specified.
Also available in Stainless Steel.
TWIN TRAC 38-3/8"
|
| Head-of-Wall Deflection Connections |
Fast Top™ Clip (FTC3, FTC5)
Used in head-of-wall deflection conditions for exterior curtain wall and interior,
nonload-bearing walls
ClarkDietrich Fast Top™ Clips are used in head-of-wall deflection conditions for in-fill
curtain-wall assemblies to provide for vertical movement. These clips are used in place
of or in combination with deflection track. They provide a positive attachment and do not
require bridging installed continuously throughout the upper most punchouts.
The Fast Top™ clip can be attached to the underside of structural members, concrete
decks or floor assemblies. Studs must be cut less than full height to enable vertical
movement up to 2-1/2" (1-1/4" up and down). Fast Top™ Clips install quickly with welds,
screws, or powder actuated fasteners. FastClip™ deflection screws are used to attach
the clip to the cold-formed framing and to ensure frictionless deflection. These clips are
also embossed with fastening patterns to ensure accurate placement of fasteners.
• Vertical movement up to 2-1/2" (1-1/4" up and 1-1/4" down).
• Available in 3-1/4” and 4-3/4” widths.
• FastClip™ Deflection Screws (included) provide frictionless slip connection.
• U.S. Patent No. 6,688,069
|
 |
Uni-Clip™ End Clip (UCEC)
14 Gauge rigid connection clip
ClarkDietrich’s Uni-Clip™ framing clip is a universal framing clip used to attach and
support numerous rigid framing conditions. The Uni-Clip™ framing clip has stiffened
corners that provide superior design values and are installed easily with screws or
powder-actuated fasteners. This clip is ideal for most rigid connections, including shear,
tension and two-axis loading.
• Designed to transfer large horizontal and vertical loads.
• Universal multi-application connector.
• Stiffened corners result in superior design values.
• Embossed fastening patterns to ensure accurate placement of fasteners.
 |
 |
EasyClip™ E-Series™ Support Clip
Feature a long leg to accommodate greater standoff for rigid connections.
EasyClip™ E-Series™ Support Clips are used for rigid stand-off connections. The 4"
wide leg provides extra length to achieve stand-off connections up to 3". They are
commonly used in by-pass wall conditions, solid blocking attachments in joist framing
and to secure rafter framing to the primary structure. These clips are pre-punched for
aster and more accurate fastener placement.
• 4" leg accommodates large standoff.
• Lengths available in 3", 5", 7", 9" and 11".
• Available in 16, 14 and 12 gauge.
|
 |
EasyClip™ S-Series™ Support Clip
Are used to secure U-channel (cold-rolled channel) to framing members for lateral
bridging and for miscellaneous rigid connections.
ClarkDietrich EasyClip™ S-Series™ support clips are commonly used for rigid
connections in window and door framing, joist, bypass or other miscellaneous connections
to secure one framing member to another, or to secure framing members to the structural
frame. This high-performance, multi-use utility clip is ideal for corner reinforcements, stair
openings, and numerous support applications. Available in a variety of lengths and
gauges, EasyClip S-Series clips are prepunched for faster and more accurate fastener
placement.
• 1-1/2" x 1-1/2" legs.
• Lengths available in 3", 5", 7", 9" and 11".
• Available in 16, 14, and 12 gauge.
 |
 |
EasyClip™ U-Series™ Clip Angles
Used to Secure U-channel to wall studs for lateral bridging
EasyClip™ U-Series™ Clip Angles are used to secure U-channel to wall studs for lateral
bridging or for miscellaneous rigid connections. U-channel is passed through the stud
knockout and an EasyClip™ U-Series™ clip is screw-attached or welded to provide a
rigid connection. EasyClip™ U-Series™ clips are prepunched for faster and more
accurate fastener placement. U-Series™ clip angles and U-channel should not be used
in bridging applications when the stud width exceeds 8".
• 1-1/2" x 1-1/2" legs.
• Lengths available in 3-3/8", 5-3/4", 7-3/4" and 9-3/4".
• Prepunched for faster and more accurate fastener placement.
 |
 |
EasyClip™ B-Series™ Clip Angles
Secures U-channel in back-to-back framing applications
EasyClip™ B-Series™ Clip Angles are used to secure U-channel to wall studs in
back-to-back framing applications and for various miscellaneous rigid connections.
The shorter length of the B-Series™ clip enables the clip to be installed inside the
C-shape. (The B-Series™ clip can also be used on single studs where the clip is
preferred to be inside the C-shape.) B-Series™ clips are prepunched for faster and
more accurate fastener placement. B-Series™ clip angles and U-channel should not be
used in lateral bridging when stud width exceeds 6".
• 1-1/2" x 1-1/2" legs.
• Available in 3", 5-1/4", 7-1/4" and 9-1/4" lengths.
• Prepunched for faster and more accurate fastener placement.
 |
 |
EasyClip™ X-Series™ Clip Angles
Used to secure U-channel to wall studs for lateral bridging
EasyClip™ X-Series™ Clip Angles are used to secure U-channel to wall studs for lateral bridging. U-Channel is passed through the stud knockout and an EasyClip™ X-Series™ clip is screw attached or welded to provide a rigid connection. X-Series™ clip angles and U-channel should not be used in lateral bridging when stud width exceeds 8". EasyClip™ X-Series™ clip angles are also used to secure one framing member to another or to attach and reinforce headers and sills in door and window openings. X-Series™ clips are prepunched for faster and more accurate fastener placement.
• 2" x 2" legs.
• Available in 3-3/8", 5-3/4", 7-3/4" and 9-3/4" lengths.
• Prepunched for faster and more accurate fastener placement.
|
 |
SwiftClip™ 150x150 LS-Series
SwiftClip™ 1-1/2" x 1-1/2" (LS-Series)
1-1/2" leg x 1-1/2" leg fixed/ridged connection clip
Pre-punched SwiftClips™ are used for multiple construction applications. They are
commonly used for lateral bracing CRC connections, header & sill connections and
floor joist hangers.
Coating: G90
Yield Strength: 50ksi
ASTM: Meets or exceeds ASTM A653/A653M
 |
 |
EasyClip™ A-Series™ End Clip
Used in knee wall connections or to reinforce jamb stud connections
at the primary frame
EasyClip™ A-Series™ End Clips are most commonly used to reinforce connections in
knee-wall applications or to reinforce jamb stud connections to the primary frame.
These clips are unpunched as the specific application will determine the appropriate
number and placement of fasteners.
• 3" x 3" legs.
• Available in 16, 14 and 12 gauge.
• A-Series™ clips are unpunched.
• Lengths available: 3" and 6".
 |
 |
EasyClip™ D & T-Series™ Anchor Clips
Provide cost effective tie-down solutions for knee walls, shear
walls and truss connections
The EasyClip™ D-Series™ & T-Series™ Anchor Clips are high-performance, cost
effective solutions for knee wall-to-foundation connections, light duty shear
wall-to-foundation connections and truss to wall connections. These multi-application
clips feature reinforced stiffening ribs that provide superior design values for maximum
performance. The EasyClip™ D-Series™ & T-Series™ Anchor Clips are designed to
resist horizontal, torsional, and vertical (uplift) loads. These clips are prepunched with a
series of attachment holes (including anchor bolt, kwik-con and screw holes) for efficient
and accurate fastener placement.
• Resist uplift, horizontal and rotational loads.
• Stiffening ribs for superior design values.
• Prepunched holes for fast attachment.
• Multipurpose applications.
 |
 |
| Bridging, Bracing + Backing Connections |
Spazzer® 9200 Bridging Bar (SPZD)
Facilitates the rapid erection of interior, nonload-bearing studs
The Spazzer 9200 Spacing Bar is a prenotched bridging and spacing bar that facilitates
the rapid erection of interior, nonload-bearing, nonstructural studs into a rigid, accurately
laid out gridwork that has excellent resistance to stud rotation and displacement.
Spazzer 9200 bar is a 20-gauge (33mil) bar that is 50" long and prenotched to hold studs
rigidly on 16" or 24" centers. The slots have been pre-engineered to hold studs in place
by utilizing “shear” to bridge studs into a rigid gridwork.
• Saves up to 40% in combined labor and material costs.
• Eliminates stud spacing layout.
• Eliminates clip angles and the labor required to install them.
• U.S. Patent Nos. 5,784,850 & 6,021,618
|
 |
Spazzer® 5400 Bridging Bar
Facilitates the rapid erection of structural wall framing
ClarkDietrich TradeReady® Spazzer® 5400 spacer bar is a pre-notched, 16-gauge,
galvanized steel spacer and bridging bar, engineered to facilitate the rapid, efficient
erection of exterior curtain wall framing, loadbearing walls and high interior partitions
constructed of structural studs. Until now, most bridging in steel studs was accomplished
with cold-rolled channel that required bridging clips or welding.
The Spazzer bridging bar is equipped with proprietary prepunched slots that reduce
installation costs up to 40% and provide excellent torsional and lateral stud restraint.
The Spazzer Bar Guard™ retainer clip or the Spazzer Snap-In Grommet should be used
to secure the Spazzer bar when used in load-bearing applications.
• Saves up to 40% in combined labor and material costs.
• Prenotched at 12", 16" and 24" intervals, so no layout is needed.
• Eliminates clip angles and the labor required to install them.
• U.S. Patent No. 6,708,460 and other patent pending.
|
 |
Spazzer® Bar Fly Clip (SFLY)
Eliminates the need for cutting and bending when using the Spazzer® 5400
Spacer Bar to facilitate rapid installation of exterior curtain wall framing
The Spazzer bar fly clip is a secure, fast and efficient way to finish a wall section when
using the TradeReady® Spazzer 5400 spacer bar to facilitate the rapid erection of curtain
wall or load-bearing framing. Traditionally, at the end of a section, the Spazzer bar would
need to be cut and bent to keep the bar in place. With the new Spazzer bar fly clip,
installation is as easy as fastening the prepunched clip to the stud and the Spazzer bar.
The excess Spazzer bar is cut and installation is complete.
The Spazzer fly clip is the perfect solution for installing off module studs with the 5400
series Spazzer bar. Simply cut the Spazzer bar just short of the stud web, and use the
Spazzer fly clip to quickly connect the Spazzer bar to the face of the stud with self-drilling
framing screws.
|
 |
Spazzer® Bar Guard™ (SPBG)
Used to secure the Spazzer bar when used in load-bearing applications
The Spazzer Bar Guard™ retainer clip is used to secure the Spazzer bar when used in
load-bearing applications. ClarkDietrich TradeReady® Spazzer® 5400 spacer bar is a
pre-notched, 16-gauge, galvanized steel spacer and bridging bar, engineered to facilitate
the rapid, efficient erection of exterior curtain wall framing, loadbearing walls and high
interior partitions constructed of structural studs.
|
 |
Danback® Flexible Wood Backing
Reduce steel stud backing installation time by up to 90%
Danback™ Flexible Wood Backing System, featuring Dricon® fire-retardant treated
wood (FRT), has made wood backing installation easy and economical-eliminating
cutting, notching, ripping and routing.
Danback provides superior connection shear and pullout strength to support and meet
even some of the heaviest loading conditions. Simply snap, flex and screw Danback into
place. The patented hinge design actually flexes around the stud and snaps into place
for a perfect fit-every time.
Dricon FRT is pressure-treated wood that is chemically treated to reduce the flamespread
and smoke development. Dricon is Class A fire retardant; it is EPA registered, NER
approved (NER-303) and complies with all national codes including the 2003 International
Building Code (IBC) and the 2003 International Residential Code Council (ICC).
Danback flexible wood backing is available with FSC-certified lumber and may contribute
LEED® points to your project.
Material: Made with Dricon fire-retardant treated wood
Dimensions: 5/18” x 48” (130mm x 1219mm)
Packaging: (250) pieces per skid
Product weight: 5.114 lbs. / piece
|
 |
Katz™ Bridging Bar
Quick, efficient method to ladder frame between parallel joists or trusses
Katz™ bridging bar is specifically manufactured to ladder frame between parallel framing
members and provide for the attachment of the top of the interior nonstructural walls when
trusses or floor joists run parallel to the walls. Katz blocks are secured to the floor joists or
roof trusses with screws or nails.
• Precut for 16" and 24" O.C. spacing.
• Coped and prepunched flanges for easy installation.
• Eliminates wood blocking and labor-intensive notching of metal framing.
|
 |
FastBack™ Backing System (FBBC)
Universal design-Works with studs in either direction
No exposed fasteners on the face of the product helps to reduce finishing time.
Inter-locked design between stud and track for baseboard backing installations cut-away
design allows backing and bracing to be installed all the way to the floor.
Available in 5-1/8” and 10-1/4” standard sizes.
•Pre-cut fire-rated wood backing sized to fit 12”, 16”, and 24” O.C. spacing. |
 |
Gusset Plates (G-Series & GP-Series)
G-Series™ Punched Gusset Plate
Prepunched gusset plates for easier and faster attachments.
G-Series™ Punched gusset plates are multipurpose connectors used in a variety of
framing connections including roof framing, header framing and shear wall applications.
Adapts to varying construction tolerances and to multiple configurations.
• Multihole shapes for proper fastening to achieve desired performance criteria
• Eliminates angled cutting
• Mill-certified 50 ksi steel
Gauge: 18 gauge (43 mils)
Design Thickness: 0.0451 inches (1.146mm)
Gauge: 16 gauge (54 mils)
Design Thickness: 0.0566 inches (1.438mm)
Gauge: 14 gauge (68 mils)
Design Thickness: 0.0713 inches (1.811mm)
Coating: G90 (Z275) hot-dipped galvanized coating
18 gauge Mill-certified SS Grade 33 ksi (230 MPa)
Yield Strength: 14 & 16 gauge Mill-certified SS Grade
50 ksi (340 MPa)
ASTM: A 653/A 653M
|
 |
GP-Series™ UNPunched Gusset Plate
Unpunched Gusset Plates are used in conjunction with X-bracing in load-bearing
shear wall assemblies to resist racking under wind and seismic loads.
Gusset Plates and diagonal tension strapping components are used in combination to
provide shear wall (racking restraint) for light-gauge load-bearing framing under wind and
seismic loads. They are normally installed on both sides of the wall directly over the
framing members and are easily covered with facing materials.
• Provides racking restraint
• Used in shear wall assemblies
• Resist uplift and shear forces
Unpunched Gusset Plates are also used to facilitate connections between chord
members for in-plane framing.
Gusset Plates and diagonal tension strapping components are used in conjunction with
X-bracing in load-bearing shear wall assemblies to resist racking under wind and seismic
loads. They are normally installed on both sides of the wall directly over the framing
members and are easily covered with facing materials.
• Provides racking restraint
• Used in shear wall assemblies
• Resist uplift and shear forces
|
 |
Universal Header Hanger (H-Series)
Used to connect box headers to jambs or beams to columns
The H-Series™ Universal Header Hanger is used to connect box headers to jambs or
beams to columns and transfer large vertical loads. This universal hanger is designed so
one part can be used for either side of the connection. The hanger also features a support
tab for proper alignment and easy installation.
The H-Series™ hanger is also prepunched with a series of round, square and triangle
holes to ensure proper fastener placement for specified loads.
• Universal application — no left or right handed.
• Support tab for easy installation.
• Multi-hole shapes for proper fastening to achieve desired loads
|
 |
| Floor Joist Framing Connections |
EasyClip™ Quick Twist Web Stiffener
Provide reinforcement at critical load points to prevent web crippling
EasyClip™ Quick Twist Web Stiffeners are used to provide reinforcement of joist webs
to prevent crippling. Web reinforcement is often required by design to enhance the load
capacity of joists. The unique design of this web stiffener allows the installer to insert the
stiffener on the inside of the joist after the joist is installed. This stiffener eliminates the
need to pre-insert traditional web stiffeners prior to joist installation. The one-piece
assembly is easily rotated in-place for a tight fit.
• Simple, post installation assembly
• Easily rotated in-place for a tight fit
• Pre-punched for easy installation of fasteners
• Solid 12 gauge construction
• One-piece assembly
Product Dimensions
3-1/2" x 7-1/4"–14" x 1-1/4"
6" x 7-1/4"–14" x 1-1/4"
Material Specifications
Gauge: 12 gauge (97mil)
Design Thickness: 0.1017 inches
Coating: G90
Yield Strength: 50ksi
ASTM: A653/A653M |
 |
TradeReady® Rim Track Splice Plate
Ideal for splicing rim joist and is easily field skewable for off-angle rim joist
connections
The Field Skewable TradeReady® Rim Track Splice Plate provides an easy and efficient
method for splicing TradeReady® Rim. This plate is also ideal for connecting and
reinforcing the rim at bay or bow window details. The center of the plate allows for easy
one-time field bending from 0 ̊ to 135 ̊.
Caution: This plate can only be bent one time.
• Ideal for bay and bow windows.
• Great for off-angle connections.
• Prepunched for easy installation.
Product Data & Ordering Information
Gauge: 18 gauge (43 mils)
Design Thickness: 0.0451 inches (1.140mm)
Yield Strength: Mill-Certified SS Grade 33 ksi (230 MPa)
Gauge: 16 gauge (54 mils)
Design Thickness: 0.0566 inches (1.438mm)
Coating: G90 (Z275) hot-dipped galvanized coating
Yield Strength: Mill-Certified SS Grade 50 ksi (340 MPa) ASTM: A 653/A 653M
|
 |
| Specialty Clips and Connectors |
Aluminum Burn Clip (AB)
Clips melt away under intense heat, allowing a fire-damaged structure to collapse,
while keeping the firewall barrier in place to protect the adjacent units.
ClarkDietrich Aluminum Burn Clips are used as part of the ClarkDietrich H-Stud Area
Separation Wall assembly and are designed to melt and break away when exposed to fire.
The clips are used to hold the area separation wall assembly in place at the floor, roof and
truss line between adjacent units.
Should a fire break out in one unit, the Aluminum Burn Clips on the fire-ridden side of the
area-separation wall will melt, allowing the wall structure for that side to collapse.
The Aluminum Burn Clips on the non-fire side will remain intact and hold the area
separation wall in place as a barrier to contain the fire within the unit of origin.
• Tested and approved with most major gypsum and shaftliner manufacturers
• Must be used in conjunction with H-Stud Area Separation Wall Assembly
• Prepunched for easy attachment
|
 |
RSIC Resilient Sound Isolation Clips
A low cost, high performance, noise control solution
The RSIC Resilient Sound Isolation Clip is used in conjunction with drywall furring channel
to fasten gypsum wallboard to various wall and floor-ceiling designs and applications,
while simultaneously providing acoustical separation (decoupling). This significantly
reduces the amount of impact and airborne sound filtering from rooms above, below and
alongside. The RSIC has been acoustically tested, and adds 15 to 20 STC points and 15
to 20 IIC points to most assemblies, reducing the noise transfer by 75 to 100%.
• Easily attaches to wood, steel or concrete.
• Adds 15 to 20 STC points to most wall and floor-ceiling assemblies.
• Reduces noise transfer by 75 to 100%.
• Ideal for condos, apartments, hotels, motels, theaters or any other structure where noise
control is a concern.
• UL fire rated for over 150 assemblies.
|
 |
Metal Furring Channel Clips (MFCC)
Quickly facilitates the attachment of metal furring channel to 1-1/2" U-channel in
ceiling assemblies
Metal Furring Channel Clips are made of galvanized wire and used to attach Metal Furring
Channels to 1-1/2" U-channels in ceiling gridwork. Clips must be installed on alternating
sides of the 1-1/2" channels. Use tie wire when clips cannot be alternated.
Clips should only be used when single-layer gypsum or single-layer veneer plaster
base
is used.
•Securely fastens furring channel to U-channel.
•Corrosion-resistant galvanized wire.
•500 pieces per box.
|
 |
Custom Fabricated Clips & Connectors
Custom connectors, clips or supports fabricated to your exact specifications
ClarkDietrich can custom fabricate just about any shape, bend, angle or specialty framing
clip, connector or support to your exact specification. These custom products are
manufactured using precision brake-forming equipment. A diverse selection of specialized
sizes and shapes are available. Prepunched holes and specialized slotting are also
available. Simply submit your dimensioned drawings to one of our customer care
representatives.
The performance and installation of custom-made products is the sole
responsibility of the design professional and engineer of record. Any customer
ordering a custom-fabricated clip, connector or support shall indemnify, defend
and hold harmless Clarkwestern Dietrich Building Systems LLC, ClarkDietrich
Building Systems, and ClarkDietrich Engineering Services for any loss or damage
arising in whole or in part.
• Wide array of custom options.
• Fully dimensioned part drawings must be provided.
• Prepunched holes and specialized slotting available.
• Precision fabrication meeting exacting specifications. |
 |
|
| |
| ©2010 AC1 SUPPLY, INC - All rights reserved | Web Design & Development by Quint Advertising, Inc |
|
|
